BOSTIK PRODUCTS

Boscocem SBR is a styrene butadiene rubber latex emulsion additive. It is designed for use as an integral bonding agent with cement-based products in slurry bonding coats, mortars, screeds, renders and tile adhesives. It is used to improve adhesion to properly prepared substrates. The tile adhesive so prepared is good forbonding alltypes oftiles. Cement based toppings, patching mortars, leveling compounds and ter razzo, Waterproof ing cement/sand renders / screeds, Bonding concrete repair mortars, Bonding agent for ceramic tiles, bricks, etc., Preparation ofspatterdash Increases flexural and tensile strength, Improves bond strength, Improves workability, Improves abrasion resistance, Reduces shrinkage and cracking, Resists chemical and water resistance, Protects from freezethawdamage, Reduces waterabsorption ofmortar. Surface Preparation Mixing Surface must be structurally sound. Remove all deteriorated concrete, dirt, oil, grease, curing compounds, coatings and allbond-inhibiting materials from surface. New concrete and masonry surfaces must be cured 28 days. Preparation work should be done by high-pressure water blast, or other appropriate mechanical means to obtain a clean, exposed aggregate surface. Saturate surface with clean water. Substrate should be saturated surface dry with no standing water during application. Follow the surface preparation directions for the product in which Boscocem SBRis being used as an admixture. Bonding slurry: Amixture of 1 : 1 . Boscocem SBR : OPC (by volume) bonding slurry is prepared and mixed in a clean container until a creamy brush consistency is obtained. Mix onlythe amount that can be used within the working life ofthe product. Polymer admixture for mortars: With mixer running, add measured quantity of Boscocem SBR, water, OPC, sand and aggregate depending on type of application (refer to the following mix designs for batching proportions). Mix to desired consistency

The disposable hygiene industry has been looking—with varied results—for a pad attachment adhesive that satisfies operational requirements, consumer performance expectations, and inspires consumer loyalty. When she’s not happy with her feminine hygiene products, you have an opportunity. Turn to Bostik. We can help you get back on track. 

Our pad attachment experts dissected the challenges faced by both manufacturers and users of pads for feminine hygiene and light urinary incontinence. We evaluated the ability of peel testing—a common surrogate for stay-in-place performance—to predict actual staying power. We examined tested adhesives currently used on sanitary napkins and compared them to consumer reviews. One thing became clear: Conventional wisdom wasn’t meeting consumer expectations. Better hold on! 

In our whitepaper, “Next-Level Stay-in-Place Testing and Adhesive Technology,” we explore: 

• What consumers—specifically women—look for in a disposable hygiene pad
• Common challenges producers experience while trying to meet her needs
• The (in)ability of peel testing to accurately reflect her experience
• Stay-in-place test methods, including Bostik’s brand-new Staybility Test
• The development of our industry advancing StayX™ Adhesive Technology 
• Excellent Bonding

It’s time to meet and exceed consumer expectations. Let us work with you to move your brand to higher levels of customer satisfaction.

Smart AdvantagesIncreases flexural and tensile strengthImproves bond strengthImproves workability SBR Latex Emulsion Additive

Boscocem SBR is a styrene butadiene rubber latex emulsion additive. It is designed for use as an integral bonding agent with cement-based products in slurry bonding coats, mortars, screeds, renders and tile adhesives. It is used to improve adhesion to properly prepared substrates. The tile adhesive so prepared is good for bonding all types of tiles.

• Increases flexural and tensile strength
• Improves bond strength
• Improves workability
• Improves abrasion resistance
• Reduces shrinkage and cracking
• Resists chemical and water resistance
• Protects from freeze-thaw damage
• Reduces water absorption of mortar

Boscocem SBR is a styrene butadiene rubber latex emulsion additive. It is designed for use as an integral bonding agent with cement-based products in slurry bonding coats, mortars, screeds, renders and tile adhesives. It is used to improve adhesion to properly prepared substrates. The tile adhesive so prepared is good forbonding alltypes oftiles. Cement based toppings, patching mortars, leveling compounds and ter razzo, Waterproof ing cement/sand renders / screeds, Bonding concrete repair mortars, Bonding agent for ceramic tiles, bricks, etc., Preparation ofspatterdash Increases flexural and tensile strength, Improves bond strength, Improves workability, Improves abrasion resistance, Reduces shrinkage and cracking, Resists chemical and water resistance, Protects from freezethawdamage, Reduces waterabsorption ofmortar

Surface Preparation Mixing Surface must be structurally sound. Remove all deteriorated concrete, dirt, oil, grease, curing compounds, coatings and allbond-inhibiting materials from surface. New concrete and masonry surfaces must be cured 28 days. Preparation work should be done by high-pressure water blast, or other appropriate mechanical means to obtain a clean, exposed aggregate surface. Saturate surface with clean water. Substrate should be saturated surface dry with no standing water during application. Follow the surface preparation directions for the product in which Boscocem SBRis being used as an admixture. Bonding slurry: Amixture of 1 : 1 . Boscocem SBR : OPC (by volume) bonding slurry is prepared and mixed in a clean container until a creamy brush consistency is obtained. Mix onlythe amount that can be used within the working life ofthe product. Polymer admixture for mortars: With mixer running, add measured quantity of Boscocem SBR, water, OPC, sand and aggregate depending on type of application (refer to the following mix designs for batching proportions). Mix to desired consistency. 

Bostik lw is a chloride free admixture and supplied as brown liquid.Concrete roof slab and screeds,
Floor screed in bath room and damp areas,
Basement slabs and walls,External plastering, 
Plastering of water tank and sumps.

Acrylic Polymer Waterproof Coating Flexi-Crete SC300 is a modified acrylic hybrid system which has many uses like waterproofing of toilets, sunken portions, roofs, swimming pools, water tanks, asbestos roofs, terraces, china chips terraces, etc. It can also be used for crack repair, and rehabilitation projects.

Bostik Flowfill Grout GP is a general purpose, non-shrink, (Class A) cementitious construction grout ideal for most void filling grouting jobs. 
Smart Advantages Ready to use, pre mixed, requires only the addition of waterCan be pumped, trowelled, rammed or flowed to areas where normal grouting methods do not sufficeCan be mixed for stiff, plastic, flowable or fluid application

About Flowfill Grout GP

Pre-hardening volume-adjusting. Controlled gaseous expansion system compensates for shrinkage and settlement before hardening occurs

Ready to use, pre mixed, requires only the addition of water

Can be pumped, trowelled, rammed or flowed to areas where normal grouting methods do not suffice

Can be mixed for stiff, plastic, flowable or fluid application

No metallic iron content to cause staining

Lower water/cement ratio reduces drying shrinkage, increases durability and reduces permeability

Recommended Uses

All general purpose grouting

Precast and pre stressed panels

Grouting in column bases

Filling core holes, rod holes and defects in concrete

Filling for hollow block walls

Caulking of joints and pipes

Read and understand the Safety Data Sheet before using this product. SDS can be acquired by visiting or by scanning the relevant QR code on pack.The substrate surface must be clean, sound and free from oil, grease, curing compound or any loose materials. It must be mechanically abraded back to a sound concrete surface. Bolts or anchor holes must be clean and free from dust or loose material. This can be achieved by blowing clean the hole. Base plates must be cleared of all rust, oil or grease. It is essential to provide air pressure relief holes for venting. Pre-Soaking It is essential to pre-soak the concrete substrate prior to application of Bostik Flowfill Grout GP. Pre-soak substrate with water for a minimum of 6 hours prior to grouting. Immediately before pouring, the excess water should be removed. In the case of bolt/anchor holes, the holes must be blown out to ensure no traces of free water are present whilst grouting. Formwork Formwork must be constructed to facilitate rapid and continuous filling, whilst remaining leak proof and water tight. Foam rubber strips or suitable sealants underneath the formwork are recommended. Unrestrained Surface As Bostik Flowfill Grout GP is an expanding grout, it is advisable not to have any unrestrained areas. Low Temperature Working At temperatures below 5°C the cure rate and strength development rate will be dramatically reduced. If early strength is required, it is advisable to use heated water and condition Bostik Flowfill Grout GP to 25°C. Do not exceed this temperature. High Temperature Working At temperatures above 30ºC, it is advisable to use water below 20ºC when mixing grout. All materials must be kept cool and away from direct sunlight. If practical, the installation area should be shaded by erecting shade

 

Bostik Patchfix Concrete is a high performance rapid setting, high early strength, shrinkage compensated repair concrete. It is a special blend of cement and aggregates supplied in a ready to use form. The addition of water and mixing produces a high strength, heavy-duty, trowellable repair concrete that minimises shut down time and allows the repair back in service in 2-3 hours.

Recommended Uses:- 

• Repairing localised patches, small or large
• Repairing concrete roadways, warehouse floors, ramps, concrete pavements
• Maintenance repairs for areas 10mm to 180mm in depth in one layer
• Emergency repair of concrete
• Patching of worn or damaged concrete
• Concrete spalling repair
• Floor repairs and overlay
• Where minimum disruption to traffic and floor shutdown is required
• Floor areas subject to high abrasion and impact

Product Details:- 

• Rapid strength gain will accept vehicle traffic in 2 hours
• High early strength
• Abrasion and weather resistance
• One component product, just add water
• Excellent bond strength to concrete substrate
• High build repairs can be carried out in a single application
• Shrinkage compensated
• Internal or external application
• Low permeability provides protection against chlorides and carbon dioxide

Smart Advantages:- 

• Rapid strength gain will accept vehicle traffic in 2 hours
• High early strength
• Abrasion and weather resistance

Geographic Availability:- 

• Australia

Your Smart Advantages:- 

• Rapid strength gain will accept vehicle traffic in 2 hours 
• Abrasion and weather resistance 
• One component product, just add water 
• Excellent bond strength to concrete substrate 
• High build repairs can be carried out in a single application 
• Shrinkage compensated 
• Internal or external application 
• Low permeability provides protection against chlorides and carbon dioxide

Uses:-
Bostik Patchfix concrete is a high performance rapid setting, high early strength, shrinkage compensated repair concrete for patching concrete roadways, pavements and floors. It is a special blend of cement and aggregates supplied in a ready to use form. The addition of water and mixing produces a high strength, heavy-duty, trowellable repair concrete that minimizes shut down time and allows the repair back in service in 2-3 hours. Bostik Patchfix Concrete can be used for:-   

• Repairing localised patches, small or large  Repairing concrete roadways, warehouse floors, ramps, concrete pavements 
• Maintenance repairs for areas 10mm to 180mm in depth in one layer 
• Emergency repair of concrete 
• Patching of worn or damaged concrete 
• Concrete spalling repair 
• Floor repairs and overlay
• Where minimum disruption to traffic and floor shutdown is required
• Floor areas subject to high abrasion and impact

Directions For Use:- 
Read and understand the Safety Data Sheet before using this product. SDS can be acquired by visiting or by scanning the relevant QR code on pack.

Application Instructions Substrate & Surface Preparartion:-
Saw cut or cut back the extremities of the repair locations to a depth of at least 10mm to avoid feather edging and to provide a square edge. Break out the complete repair area to a minimum depth of 10mm up to sawn edge. Clean the surface and remove any dust, unsound or contaminated material, plaster, oil, paint, grease, corrosion deposits or algae.

Hydroment 476 Crete HSAcrylic latex based water proofing additive and bonding agent
Product overviewHydroment 476 Crete HS is a specially formulated acrylic admixture used in place of Water to fortify leveling screeds, renders and waterproofing additive.Read less.

Features & Benefits

• Good waterproofing property
• No degradation on long term exposure
• Excellent bonding properties
• Enhances strength and durability of repair mortar
• Suitable for external and internal repairs

Product Description

Hydroment 476 Crete HS is a specially formulated acrylic admixture used in place of Water to fortify leveling screeds, renders and waterproofing additive. Related market & applicationsWaterproofing

Recommended Uses

Waterproofing ofwatertanks, roofs, balconies, terraces, wet areas, swimming pools and fountains. Bonding old to newconcrete. Additive for repairmortar.

Surface should be free from oil, wax, oranyother contaminants. Ensure the substrate is sound before application Wet the substrate before coating. Mix cement and polymer in the ratio of 2:1 parts by weight to get uniform and consistent slurry by using lowspeed stirrer. Applymaterialbystiffbrush. Minimum two coats to be applied in the intervalof 5-6 hours. Mix frequentlyto avoid setting during application Cure forthree days. 1sq.m/kg mix/in 2 coats Wet the substrate before application. Apply directly or mix cement and polymer in the ratio of 2:1 parts by weight to get uniform and lump free, consistent slurry 

Storage & Shelflife

Hydroment 476 Crete HS as supplied shall be stored in a cool and dry place away from sunlight, moisture and high humidity and have a shelf life of 12 months in the originalpacking.

Health & Safety

Hydroment 476 Crete HS is non-toxic and has no known effects. Prolonged contact with skin should be avoided. Any splashes should be washed well with water. The use of rubber gloves and safety glasses is recommended. Any splashes on eyes should be flushed immediately with plenty of clean water and medicaltreatment sought.

Warranty

Whilst Bostik India P Ltd., strives to ensure that any advice, information or recommendation given are appropriate and correct, it cannot accept any liability directly or indirectly arising out of the products, since the method and place of application of the products are beyond its control. Its guarantee is therefore limited to the qualityofmaterials delivered 

Bostik Maxi Sealant Gun is a universal joint and glue chair that fits cartridges up to 300 ml. The cradle of the joint gun ensures that the cartridge is held in place and is at the same time rotatable so that the joint tip has the right angle in relation to the surface.

Silicone based water repellent. Magic repellent. We have 13 years experience. We have provided high quality product as market trend. Customer satisfaction important for us.

Ep bond is a two component bonding agent when mixed and allowed to set produces bond of immense strength.

Bostik plug leak is fast setting hydraulic cement based waterproofing compound. Basement and pits,RCC water tanks, concrete pipes, sewage system, water retaining structures.

Bostik elastcoat is a high performance elastameric acrylic based waterproofing coating with antifungal and crack bridging ability. Recommended for protection of exterior cementitious surfaces.

Bostik sealant products are specially formulated to prevent the migration or rise of moisture to extend the duration of your construction

• Bostik Anchor Grout is polyester resin based grout material suitably blended with a hardening compound and fillers and supplied as a pre measured, two part, resin grout. 

• Delivery Time: One day
• Packaging Details: 1kg package

Joint compound (also known as drywall compound, drywall mud, or mastic) is a white powder of primarily gypsum dust mixed with water to form a paste the consistency of cake frosting, which is used with paper or fiber joint tape to seal joints between sheets of drywall to create a seamless base for paint on interior ...

Bostik Elastcoat is high performance elastameric acrylic based waterproofing coating with anti-fungal and crack bridging ability. Recommended for protection of exterior cementitious surfaces.

Product overview

Bostik Flashband Self Adhesive Flashing Tape for Roofs is a flexible bitumen strip that bonds instantly to most building materials to provide a permanent, watertight seal.

Flashband is easily applied using just hand pressure and a seam roller and is ideal for new build, maintenance and repair projects, including:

 

Roofing

• Replace damaged lead flashing
• Seal upstands and eve pieces
• Roof capping
• Edge flashing on roofing felt
• Repair roofing felt or joints on flat roofs

 

Drainage

• Seal or repair valley gutters, guttering and down pipes

 

Flashband has four layers of protection, meaning it’s both tear and impact resistant and can withstand extreme temperatures of up to 100oC.

 

Four Layers Of Protection

• Lacquer coating
• Heavy duty aluminium foil
• Tear resistant polyester membrane
• Polymer enhanced bitumen adhesive

 Key Features

• Instant watertight seal
• Quick and easy application
• For new build or emergency repairs

Instant watertight seal, For new build or emergency repairs. Quick and easy application USES Bostik Flashband Self Adhesive Flashing Tape for Roofs is a self-adhesive sealing bitumen strip which bonds instantly to provide a permanent watertight seal in all climates. Bostik Flashband Self Adhesive Flashing Tape for Roofs is easily applied using hand pressure and a seam roller, with no requirement for special equipment for cutting, forming or fixing. Bonds to most building materials including brick, masonry, slates, concrete roof tiles, wood, metal, concrete, terracotta tiles, glass, roofing felt, and rigid plastics. Applications include a large variety of original construction and maintenance situations including repairing lead flashing, sealing valley gutters, mending leaks in drain pipes and guttering, greenhouse repairs, protecting glazing bars, protecting insulation for pipes and tanks, repairing roofing felt joints on flat roofs. 

Boscolastic is a two components flexible acrylic polymer cementitious waterproofing coating. Boscolastic has excellent weathering resistance and crack bridging property.

Bostik Elastcoat is a high performance elastameric acrylic based waterproofing coating with antifungal and crack bridging ability. Recommended for protection of exterior cementitious surfaces

Epoxy cote UW is a 100% solids containing pigmented two component system based on liquid epoxy resin with a amine hardener

BOSTIK BLOCK P530 BOSCOSEAL PU D IS A ONE COMPONENT RAPID DRYING WATER BASED POLYURETHANE WATERPROOFING MEMBRANE SYSTEM.

• Delivery Time: One day

BLOCK P550 BOSCO SEAL PUW IS A SINGLE COMPONENT SCIENTIFIC BLEND OF POLYURETHANE RESINS, PERFORMANCE ADDITIVES, AND BITUMEN MODIFIED WITH WATER DISPERSIBLE POLYURETHANE.

• Delivery Time: ONE DAY
• Packaging Details: BOSTIK BLOCK P550 BOSCO SEAL PUW (20kg)

Application procedure

• Fast setting water plug
• Apply to leakage area, remove loose material and clear it properly
• Add bostik plug into water in ratio 3:1 by volume
• Mix to a stiff paste consistency
• Apply on leakage area and hold it with pressure for 2-3 minutes till plug leak hardness.
• Repeat the above procedure to plug the entire leak.
• The contents of this package have been specially packed for the exclusive use of construction and other industry as raw material or for the purpose of servicing many industries.

The disposable hygiene industry has been looking—with varied results—for a pad attachment adhesive that satisfies operational requirements, consumer performance expectations, and inspires consumer loyalty. When she’s not happy with her feminine hygiene products, you have an opportunity. Turn to Bostik. We can help you get back on track. 

Our pad attachment experts dissected the challenges faced by both manufacturers and users of pads for feminine hygiene and light urinary incontinence. We evaluated the ability of peel testing—a common surrogate for stay-in-place performance—to predict actual staying power. We examined tested adhesives currently used on sanitary napkins and compared them to consumer reviews. One thing became clear: Conventional wisdom wasn’t meeting consumer expectations.

Better hold on! In our whitepaper, “Next-Level Stay-in-Place Testing and Adhesive Technology,” we explore: 

• What consumers—specifically women—look for in a disposable hygiene pad
• Common challenges producers experience while trying to meet her needs
• The (in)ability of peel testing to accurately reflect her experience
• Stay-in-place test methods, including Bostik’s brand-new Staybility Test
• The development of our industry advancing StayX™ Adhesive Technology 

It’s time to meet and exceed consumer expectations. Let us work with you to move your brand to higher levels of customer satisfaction.

Bostik Plug Leak is fast setting hydraulic cement based waterplugging compound Stop active leaks Filling holes Anchoring Equipment and machinery Concrete Patching Sealing cracks Basement and Pits Easyto mix and Finish Extremelyshort setting time Highlyversatile

Identify the leakage area, remove loose material and clean properly. Areas treated with product must be free ofdust and anyforeign matterpriorto topping application. Add Bostik Plug Leak into water in the ratio of 3:1 by volume.

Mix stiffpaste consistency Apply with gloved hand or trowel to clean and sound substrate Applyon leakage area and hold it with pressure for 2-3 minutes tillmaterialhardens Repeat the above procedure to plug the entire leak Use onlyon cementitious substrate Hand glove to be used during application Plug Leak is supplied in 1and 5 kg Plug Leak as supplied shall be stored in a cool and dry place away from sunlight, moisture and high humidity and have a shelf life of 12 months in the original packing. Plug leak is blend of cement, fast set powder and modifiers. Prolonged contact with skin should be avoided. Any splashes should be washed well with water. The use of rubber gloves and safety glasses is recommended. Any splashes on eyes should be flushed immediately with plenty of clean water and medical treatment sought. 

Bostik cwp is a surface, applied, internal crystalline waterproofing material, which waterproofs and protect concrete in depth. It consists of Portland cement, specially treated quartz sand and a compound of active  chemicals. Bostik cwp needs water only to be mixed prior to the application. When bostik is applied to a concrete surfaces the active chemicals combine with the free lime and moisture present in the capillary tracts of the concrete to form an insoluble, crystalline structure. These crystals fill the pores and minor shrinkage cracks in the concrete to prevent any further ingress, still allowing the concrete to breathe.

It is a blend of various epoxy resins and coal tar. It is commonly used to make high solids coatings or paints to provide moisture protection for underground systems like pipelines, water treatment facilities, clarifiers and tanks; it is further used in the sewage industry and for prevention from microorganisms.

Bostik Elastcoat is a high performance elastameric acrylic based waterproofing coating with anti-fungal and crack bridging ability. Recommended for protection of exterior cementitious surfaces.

Bostik crack fill is a high performance polymer modified cementitious crack sealer for sealing/ repairing internal and external crack in plasters and masonry surfaces.

Fill A gap is a general purpose water based one part gunnable, paintable actually gap filler. Easy to use, economical sealant and provide excellent adhesion for gaps in low movement joints.

For use efflorescence problerm at walls

Styrene butadiene based mortar modifying and bonding agent 

Styrene butadiene based mortar modifying and bonding agent.

Stuctural crack repair material ,this material two type use dirctly and machine injection 

Product overview

Bostik Moisture seal is a two part water based epoxy coating designed as a moisture and vapour barrier membrane to prevent water seepage and permeation through concrete floors. The product shows excellent adhesion and acts as a surface preparation for subsequent adhesives when laying floor coverings of all kinds.

Recommended Uses

• As a water vapour barrier in the building and construction industry.
• Compatible with a wide range of coverings.
• Can be used with the Bostik Ultraset flooring adhesive and Dampfix waterproofing ranges.
• Vapour barrier and primer prior to the application of cementitious floor screeds or self levelling compounds.
• Barrier coating over freshly laid (green), hardened concrete.
• As a vapour barrier on concrete or masonry prior to the application of timber flooring or panels.

Hydrostatic pressure tested to ASTM1306C-05A –exceeds 45psi or 310kPa− Water vapor transmission rate tested to ASTM E96/Eat <0.28g/h/m2*− Water based− Easy clean− Can be applied to damp surfaces− Non-flammable− Low odour− Excellent adhesion to most substrates includingbricks, masonry, concrete, compressed fibreboard,stone and timber− Convenient equal parts mixing ratio by weight or byvolume 
Uses For sealing concrete and masonry surfaces fromwater ingress or rising damp.− Can be used for waterproofing basements, concretetanks and reservoirs, lift wells, tunnels and subways.− Can be used with the Bostik Ultraset flooring adhesiveand Dampfix waterproofing ranges.− Vapour barrier and primer prior to the application ofcementitious floor screeds or self-levellingcompounds.− Barrier coating over freshly laid (green), hardenedconcrete.− As a vapour barrier on concrete or masonry prior tothe application of timber flooring or panels.− Compatible with a wide range of coverings.

Bostik Fill-A-Gap is a one-part water based, paintable acrylic gap filler. It is a general purpose, gun able onepart water based, acrylic gap filler. This easy to use, economical sealant provides excellent adhesion for gaps in lowmovement joints. Sealing cracks in plasterboard Sealing windowand doorframes Sealing around ceramic tiles Sealing lowmovement joints Crack filling priorto painting Sealing cracks in brickwork and concrete Sealing between light partition walls Sealing skirting and architraves Excellent sealing and adhesion properties Skins within 15 minutes After2 hours can be over- painted with acrylic paint Once fullycured (2-3 days) oilbased paint can be used Interior/ Exterioruse High bond strength Once cured,excellent water resistance Bostik FillA-Gap can be painted overwith most types of paint. In most cases Fill - A- Gap can be painted over in 2 hours, this is dependent on gap size and depth. In generallargerthe gap size longerthe drying time. The estimated linear metre yield per pack size is recommended in the following table. No allowance has been made forwaste or irregular joint geometry 400 gm catridge, 1, 5 & 10 kg Containers. Store in a cool dry conditions for a shelf life of 24 months. Store awayfrom oxidising agents and acids. 

• Packaging Details: 1 kg

Contractors using PU Injections usually drill a hole into the problem area, where the PU is then pumped into the hole. The chemical composition in the injection is then triggered to expand and fill up the walls or ceiling, blindly covering the whole area in hopes of filling in these hairline cracks

Acrylic latex based waterproofing additive cum bonding agent. Waterproofing of water tanks, roofs, balconies, terraces, wet areas, reservoir, swimming pools and fountains. Bonding old to new concrete. Additives for repair mortar.

Bostik All Purpose Silicone is a premium silicone sealant. Excellent UV and weather resistance, low odour and flexible. Ideal for sealing and adhering a range of building materials such as steel, metal, aluminium, timber, glass, concrete, fibreglass, brick and masonry. Neutral cure, interior/exterior use.

• Delivery Time: 1
• Packaging Details: BATTLE

Bostik crack fill is high performance polymer modified cementitious crack sealer for sealing and repairing internal and external cracks in plasters and masonry surface.