construction chemical

Acrylic latex based waterproofing additive cum bonding agent.DESCRIPTION Boscocrete is a specially formulated acrylic admixture used in place of water to fortify leveling screeds, renders and waterproofing additive RECOMMENDED USES Waterproofing of water tanks, roofs, balconies, terraces, wet areas, swimming pools

MYK LATICRETE SP 100 , kitchen, bathroom, swimming pools, fountains, water bodies, hospitals, operation theatre's, sterilization rooms, restaurants, cafeterias, light industrial applications and high traffic areas. It is NOT a waterproofing material for joints or surfaces.

• Packaging Details: 1kg,5kg

It is a smooth and creamy polymer based adhesive for installing small to medium format ceramic wall and floor tiles, vitrified tiles, small format natural stones in interior areas using this one component of installation a. .

• Packaging Details: MYK LATICRETE TILE ADHESIVE 307, COLOURS: WHITE AND GREY FOR AVAILABLE PACKING (20KG)

EP 305: Is a two part, thixotropic, high performance epoxy adhesive and repair compound.concrete repair application.

• Delivery Time: One hours

CL 11 has been especially designed to produce a smooth flat surface when applied to hard, rigid sub floors such as cement sand screeds, concrete etc.

Patch repairs of low medium strength concrete structures (<M45), 
Thixotropic,non sag, excellent bond strength, crack resin. Fibre reinforced.

Surface Preparation: All surfaces should be between 40° F(4° C) and 95° F(35° C) and structurally sound, clean and free of all dirt, oil, grease, loose peeling paint, laitance, concrete sealers or curing compounds. Substrates must be compact and consistent, free from any rising dampness, with no loose, flaky, or imperfectly anchored parts. The substrate must be stable, without cracks and have already completed the curing period of hygrometric shrinkage. Uneven areas must be corrected with suitable smoothing and finishing products. Installation shall be made on a dry surface. New concrete slabs must be damp cured and at least 28 days old prior to application. All slabs must be plumb and true to within 1/4” (6mm) in 10ft (3m). Expansion joints shall be provided through the tile work from all construction or expansion joints in the substrate. Follow ANSI Specification AN-3.8 “Requirements for Expansion Joints” or TCA Detail EJ171-91 “Expansion Joints”. Do not cover expansion joints with mortar. Glass Mesh Mortar Unit: follow TCA installation detail W244. Mixing: MYK Laticrete PUA 212 is prepared by mixing together parts A and B from the bottom upwards, using a low-rev (≈ 400/min.) helicoidal agitator, with the preset ratio of 1: 25 of the packs. Pour part B into the bucket containing part A, being careful to mix the two parts uniformly until a smooth, even coloured mixture is obtained. The user must mix a quantity of adhesive which can be consumed within 1 hour at +25 °C / 50% R.H. Packs of MYK Laticrete PUA 212 adhesive must be stored at a temperature of ≈ +25 °C for at least 2/3 days prior to use. APPLICATION: a) Tile/Stone Apply adhesive to the substrate with the flat side of the trowel, pressing firmly to work into surface. Comb on additional adhesive with the notched side. Use the proper sized notched trowel to ensure full bedding of the tile. Spread as much adhesive as can be covered with tile in 10 minutes. Back butterlarge format tiles (> 12”x12”) to provide full bedding and firm support. Place tiles into wet, sticky adhesive and beat in using a beating block and rubber mallet to imbed tile and adjust level. Check adhesive for complete coverage by periodically removing a tile and inspecting bedding adhesive transfer onto back of tile.If adhesive is skinned over (not sticky), remove and replace with fresh adhesive.b) Glass Mosaic tiles The MYK LATICRETE PUA 212 adhesive shall be applied to the surface to be tiled with a notched trowel using a scraping motion to work the adhesive into good contact with the surface to be covered. Notch trowel with notches approximately 4mm is recommended to get a bed thickness of 1.5-2mm. V-notch of 3mm also can be used to get bed thickness of 1.5mm. Apply only so much that can be covered with tile within 10-15 minutesor while the adhesive surface is still tacky. The Glass Mosaic tiles shall then be set in place and beaten gently with mallet or grouting float to insure 100% full bedding. Tiles shall be aligned to achieve uniform joints and then allowed to set until firm.Excess adhesive must be cleaned from the surface of the tile with a wet cloth or sponge while the adhesive is fresh and has not hardened.After the tiles are set firm, the face of the sheets of front mounted glass mosaic tiles shall then be dampened and the face mount paper can be removed.Installation of Tile / Stone on Drywall boards: When the installation of tile or stone is done using MYK Laticrete PUA 212, on drywall boards like cement backer board, wood board, plywood board, calcium silicate board, gypsum wall board, it is advised to provide spacers and fill the resulting grout joints with flexible materials like MYK Laticrete Stellar Grout / silicone sealant / acrylic sealant.

• Delivery Time: One day
• Packaging Details: 8 kg

Acrylic latex based waterproofing additive cum bonding agent.DESCRIPTION Boscocrete is a specially formulated acrylic admixture used in place of water to fortify leveling screeds, renders and waterproofing additive RECOMMENDED USES Waterproofing of water tanks, roofs, balconies, terraces, wet areas, swimming pools